The water supply line is usually located under the kitchen sink. If the water pressure is too low, the valve may not close fully once the power is shut off. The water inlet valve requires a minimum of 20 psi to shut off properly. The fill tube going into the ice maker can sometimes freeze, which prevents water from getting to the ice maker. Make sure that the tube that goes into the ice maker cup is in correctly and there are no holes in that cup. To test this turn the icemaker off for 3-4 hours. If the icemaker appears to be leaking water into the ice bucket or onto the floor: If the icemaker is leaking water onto the floor: For service, please schedule an appointment with GE Appliances Factory Service. Sometimes however, water intake problems may be the ice maker, but those are usually limited to minor overfill problems or an incomplete rotation cycle. First, the ice maker receives the water through a small supply line from the house, taking the water through a fill valve that is controlled by a thermostat. If there is no water going to the icemaker in your refrigerator, there are a few things to check. Be sure the water line fittings are secure. The condensation drain is meant to drain out any excess water or ice melt from the freezer compartment to keep things tidy. This will shut off the water to the icemaker. Fits most applications. No more dealing with emptying and refilling ice trays. Today, we’re here to explore why your ice maker is leaking, how to identify the cause, and a few practical tips on how to solve each potential cause of the leak. How can this be fixed? KitchenAid Ice Maker KIMS8 Leaking ... if your KIMS8 ice maker dripping water, leaking water into bin or leaks water, the following info will help you identify the problem. However, if something goes wrong with this little water distribution system, then it can easily cause a leak coming directly out of the ice maker. The discharge tube inside was full of ice because the ice maker fill valve was old and was leaking ever so slightly. Usually this is a simple defrost drain tube issue with the refrigerator leaking water. If it doesn't then you have a problem where the water enters into the ice maker. If the water pressure is too low, the valve may not close fully once the power is shut off. Heres what you do, put a low amount of water into the ice maker (make sure there isnt ice or water in it already) and see if it leaks. Before checking on the valve, unplug the refrigerator and turn off the valve’s water supply. If the ice maker leaks water, first check for leaks in the house water supply line connected to the water inlet valve, the drain line and the drain pump. If there are still issues with ice blocks or water leaking in the ice maker area, service is … The line going from the ice maker fill valve ruptured and leaked water on the floor. s.channel = "Service_Support"; Turn off the water supply source to the unit. s.prop3 = s.channel + "|Support Search"; //s.eVar15 = ""; All other parts of the fridge are working fine. The ice maker auger is free of frost, the ice tray is operating correctly, and water does not drip into the refrigerator when using or making ice. The theory is that refrigerators leak when condensation from defrost builds up and can’t find the drain. The resulting water falls into a drain sending it to a pan to evaporate. The location of the water inlet valve depends on the manufacturer but Kenmore ice maker and Whirlpool ice maker water inlet valves are typically located behind your refrigerator. There is also water visible on the white rubber seal from the ice "chute" to the ice maker inside the door. To verify and repair this, the unit … If water is dripping from the housing, this is not normal and should be looked into. If the icemaker appears to be leaking water into the ice bucket or onto the floor: Be sure the water line fittings are secure. This melting may manifest as the leaking you were perceived as coming from the ice maker. Check the water pressure to determine if it is at least 20 psi. So, if your D7824702 ice maker dripping water, leaking water into bin or leaks water, the following info will help you identify the problem. When this happens, new ice can’t get down the chute and melting is the only solution without help. Sometimes they get clogged, sometimes they stop producing ice and, perhaps the worst, sometimes the start leaking all over the freezer and floor. Take a look inside your ice maker housing to identify the fill valve and fill cup scenario. And the ice stored inside the ice maker tends to be wet and or slushy as it gets closer to the exit point of the ice maker. s.hier1 = s.prop5; The fill valve must be aligned with the fill cup in order for the water to be caught and frozen into cubes. The valve sends the water through a tube to the ice mold, then the water freezes, and the thermostat then turns off. Open the freezer drawer and remove anything that keeps you from seeing the icemaker and turn the icemaker on. // Image call You may also find that freezer burn or even fallen and refrozen ice cubes are the source of the drain blockage and of the leaks that occurred when the water could not drain.